Having trouble with your HP notebook boot device not being found? Find out how to fix it here.
Perform a Hard Reset
Performing a hard reset can often resolve the issue of a “Boot Device Not Found” error on an HP Notebook.
To do a hard reset, follow these steps:
1. Disconnect all external devices, such as USB flash drives or external hard drives, from the laptop.
2. Turn off the laptop and disconnect the power cord.
3. Remove the battery from the laptop (if it’s removable).
4. Press and hold the power button for about 15 seconds to drain any residual power from the laptop.
5. Reinsert the battery (if it was removed) and connect the power cord.
6. Press the power button to turn on the laptop.
7. If the error message still appears, try accessing the BIOS by pressing the appropriate key (usually Esc, F1, F2, or F10) during startup.
8. Once in the BIOS, navigate to the “Boot” or “Boot Options” menu.
9. Make sure that the internal hard drive is selected as the primary boot device.
10. Save the changes and exit the BIOS.
11. If the issue persists, it may be necessary to check the hard drive for any errors or issues.
12. Create a boot disk or USB drive with a disk partitioning tool like EaseUS Partition Master.
13. Boot the laptop from the boot disk or USB drive.
14. Use the disk partitioning tool to check and repair any errors on the hard drive.
15. Once the repair process is complete, restart the laptop and check if the error message has been resolved.
Performing a hard reset can help in resolving the “Boot Device Not Found” error on an HP Notebook. If the issue persists, it may indicate a more serious problem with the hard drive or computer hardware. In such cases, it’s recommended to seek professional assistance or contact HP support for further troubleshooting.
Change Boot Order
- Restart the HP notebook and press the Esc key repeatedly until the Startup Menu appears.
- Press the F9 key to open the Boot Device Options menu.
- Use the arrow keys to highlight the desired boot device, such as the hard drive, and press Enter.
- If the desired boot device is not listed, use the arrow keys to select the Boot From EFI File option.
- Press the Enter key, and navigate to the EFI file that corresponds to the boot device (e.g., Windows Boot Manager for the hard drive).
- Press Enter again to boot from the selected EFI file.
- If the issue persists, restart the notebook and press the F10 key to access the BIOS setup.
- Go to the System Configuration tab and select Boot Options.
- Locate the Boot Order or Boot Sequence option.
- Use the arrow keys to move the desired boot device to the top of the list.
- Save the changes by pressing the F10 key and then selecting Yes.
- Exit the BIOS setup and restart the notebook.
Restore BIOS Default Settings
To restore the BIOS default settings on an HP notebook and fix the “Boot Device Not Found” issue, follow these steps:
1. Start by turning on your HP notebook and repeatedly pressing the Esc key until the startup menu appears.
2. Press the F10 key to access the BIOS setup utility.
3. In the BIOS setup utility, navigate to the System Configuration tab using the arrow keys on your keyboard.
4. Locate the Boot Options menu and select it.
5. Look for an option called Secure Boot and set it to Disabled.
6. Next, find the Legacy Support option and set it to Enabled.
7. Save the changes by pressing the F10 key and choose Yes to confirm.
8. Exit the BIOS setup utility and restart your HP notebook.
9. Once the notebook restarts, press the F9 key repeatedly to bring up the Boot Device Options menu.
10. Select your desired boot device, such as the hard drive or the USB flash drive containing your operating system.
11. If you’re still experiencing the “Boot Device Not Found” issue, you may need to check your hard drive for any errors or bad sectors. Use a reliable partition manager tool like EaseUS Partition Master to scan and repair your hard drive.
12. If the issue persists, it’s recommended to contact HP customer support for further assistance.
By restoring the BIOS default settings and ensuring the correct boot device is selected, you should be able to fix the “Boot Device Not Found” issue on your HP notebook.
Check and Test Hard Drive
| Step | Description |
|---|---|
| 1 | Restart your HP notebook and press the F2 key repeatedly to access the BIOS settings. |
| 2 | Navigate to the “System Configuration” tab in the BIOS menu. |
| 3 | Select “Boot Options” and then “Internal Hard Drive” from the list. |
| 4 | Check if the hard drive is detected by the BIOS. If not, there may be a hardware issue. |
| 5 | Exit the BIOS and restart your notebook. |
| 6 | If the issue persists, you can run a hard drive test to identify any errors. |
| 7 | Restart your notebook and press the F2 key to access the BIOS settings again. |
| 8 | Navigate to the “System Diagnostics” tab in the BIOS menu. |
| 9 | Select “Hard Drive Test” and follow the on-screen instructions to complete the test. |
| 10 | If any errors are detected, you may need to replace the hard drive. |
By following these steps, you should be able to check and test your hard drive to resolve the “HP Notebook Boot Device Not Found” error. If the problem persists, it is recommended to contact HP support for further assistance.
Rebuild MBR
To rebuild the MBR on your HP Notebook and fix the “Boot Device Not Found” error, follow these steps:
1. Start your computer and immediately press the Esc key repeatedly until the startup menu appears.
2. Press the F10 key to open the BIOS setup utility.
3. Navigate to the System Configuration tab using the arrow keys.
4. Select Boot Options and press Enter.
5. Under the Boot Order section, make sure that the Internal CD/DVD ROM Drive is listed as the first boot device. If not, use the arrow keys to move it to the top of the list.
6. Press F10 to save the changes and exit the BIOS setup utility.
7. Insert a bootable Windows installation DVD or a bootable USB flash drive into your computer.
8. Restart your computer and press any key when prompted to boot from the DVD or USB.
9. Follow the on-screen instructions to reach the Windows Setup screen.
10. Select your language, time, and currency preferences, and click Next.
11. On the next screen, click Repair your computer.
12. In the Choose an option screen, click on Troubleshoot.
13. Then, click on Advanced options.
14. Select Command Prompt from the list.
15. In the Command Prompt window, type the following command and press Enter: bootrec /fixmbr
16. Wait for the process to complete, and then type exit to close the Command Prompt.
17. Restart your computer and remove the Windows installation DVD or USB.
If the MBR was the cause of the “Boot Device Not Found” error, this process should fix it and allow your HP Notebook to boot normally.
Reset Your PC
To reset your HP Notebook and fix the “Boot Device Not Found” issue, follow these steps:
1. Start by shutting down your computer completely.
2. Press the power button to turn it on, and immediately start tapping the F11 key on your keyboard.
3. This will bring up the Windows Recovery Environment menu.
4. Use the arrow keys to navigate to the “Troubleshoot” option and press Enter.
5. In the next menu, select “Reset this PC” and then choose “Remove everything” to perform a complete reset.
6. You may be prompted to choose between “Just remove my files” or “Remove files and clean the drive“. Select the option that suits your needs and click on “Reset“.
7. Your PC will now begin the reset process, which may take some time. Make sure your computer is plugged into a power source to avoid any interruptions.
8. Once the reset is complete, your computer will restart and take you through the initial setup process, just like when you first bought it.
9. Follow the on-screen instructions to set up your computer and personalize your settings.
FAQ
Why is my laptop showing no bootable device?
Your laptop is showing no bootable device because it cannot find the device or file that is supposed to boot the system. This could be due to reasons such as the hard drive or partition not being detected or the computer being set to boot from an unbootable device.
How do I fix my HP laptop operating system not found?
To fix an HP laptop with the “Operating System Not Found” issue, start by restarting your computer. Then, remove any unnecessary flash drives or disks and ensure that the hard drive with the operating system is set as the first boot device in the BIOS.
How do I fix my HP laptop when it says boot device not found?
To fix an HP laptop when it says “boot device not found,” start by turning off the computer and waiting for five seconds. Then, press the power button to start the computer and repeatedly press the f10 key to enter the BIOS setup menu. Once in the BIOS setup screen, press f9 to select and load the BIOS setup default settings. Finally, press f10 to save and exit.
How do I factory reset my HP laptop that won’t boot?
To factory reset an HP laptop that won’t boot, you can access the Windows Recovery Environment. Select Troubleshoot from the Choose an option screen, then choose Reset this PC and follow the instructions provided.
